click

Inrush Current Là Gì – Thuật Ngữ Chuyên Ngành Điện

Inrush Current La Gi Thuat Ngu Chuyen Nganh Dien

Inrush Current Là Gì – Thuật Ngữ Chuyên Ngành Điện

What is Inrush Current?

Inrush current is the instantaneous high input current drawn by a power supply or electrical equipment at turn-on. This arises due to, the high initial currents required to, charge the capacitors và inductors or transformers. Bài Viết: Inrush current là gì The inrush current is also known as the switch–on surge, or the input surge current. At turn-on, the discharged capacitors in power supplies offer low impedance that allows high currents to, flow into the circuit as they charge from zero to, their maximum values. These currents can be as high as 20 times the steady state currents. Even though it only lasts for about 10ms it takes between 30 và 40 cycles for the current to, stabilize to, the normal operating value. If not limited, the high currents can damage the equipment in addition to, producing voltage dips in the supply line và causing malfunctioning of other equipment powered from the same supply.

Inrush current specifications

High inrush currents indicate more áp lực đè nén, đè nén on the rectifier components và hence lower reliability. The inrush current is specified in terms of: Average during a half cycle or peak: – where peak is about 40% larger than the averageVoltage range – 120V or 240VOperating temperature range in which the limiting technique is effective

Xem Ngay:  Cách tính nửa chu vi hình chữ nhật là gì
*

Current waveform when the device is powered up – Image Credit

Limiting inrush currents

The two commonly used protection methods are, the passive, where a resistive current limiting device is connected in series with the supply, và the active which uses an electronic circuit consisting of resistors, a switching device và a control circuit.Resistor in Series For small wattage supplies, the resistor is connected in series with the power input line. However, the method is not suitable in larger power supplies due to, inefficiency caused by the high power dissipation và losses in the series resistor.

*

Image Credit

NTC thermistors

The method uses negative temperature coefficient (NTC) resistor connected in series with the power input line.At ambient temperature the NTC device exhibits a high resistance, when the power is turned-on, the high resistance limits the amount of inrush current flowing into the circuit. As the current flows, the thermistor temperature increases thereby reducing the resistance significantly. This stabilizes at less than one ohm, và is able to, allow the steady state current to, flow into the circuit. Xem Ngay: Trade Coin Là Gì – Bật Mí
chiêu thức Trade Coin Hiệu Quả Nhất

Parallel electronic switch

Using an electronic switch or relay in parallel with the thermistors or resistor. The currently limiting device offers high resistance at startup after which the switch is turned on to, short circuit the device. The method ensures that thermistor is able to, cool down to, its initial resistance và be ready to, protect against a subsequent surge in case of a power failure và resumption, or when one switches off an equipment và then turns it one immediately.

Xem Ngay:  Ask After Là Gì - Quá Khứ Của Ask Là Gì

Active circuits

An active circuit comprises of resistors, transistors, triacs or thyristors và a control circuit to, drive the switching device. These are suitable for applications requiring hot restart capabilities. The choice of the protection method depends on frequency of inrush currents, cost, equipment power level, reliability expected và performance. The NTC thermistor is widely used as the limiting device và preferred for its simple design và low cost as compared to, the active circuit, however, it has some drawbacks which make it unsuitable for use in extreme weather conditions or for sensitive applications. Xem Ngay: Trực Thuộc Tiếng Anh Là Gì, đô thị Trực Thuộc Trung Ương Factors considered when designing for inrush current limiting. Load capacitance valueSteady currentAmbient temperatureSupply voltageRequired current reduction of the inrush current

Soft start function, low inrush current power supplies

*

300W 2U 48VDC Input ATX Power Supply

*

160W PS2 DC-DC AT Power Supply- SDD-160-12 Thể Loại: Share trình diễn Kiến Thức Cộng Đồng

Bài Viết: Inrush Current Là Gì – Thuật Ngữ Chuyên Ngành Điện Thể Loại: LÀ GÌ Nguồn Blog là gì: https://hethongbokhoe.com Inrush Current Là Gì – Thuật Ngữ Chuyên Ngành Điện

Leave a Reply

Your email address will not be published. Required fields are marked *